Please Call for Special Orders : 403-287-5340
No customer reviews for the moment.
Ramset's T4Mag is built to be easy to use especially overhead.
The Premier Fastening System for Commercial Drywall Contractors!
Build
Ramset’s T4MAG is the best-balanced tool available and is easy to use overhead.
With 30% more power to work in the toughest concrete, this tool will drive your job site productivity and result in lower user fatigue and downtime.
The Power of the T4MAG allows you to consistently shoot where no other gas tool has gone before.
The .125 diameter pin is specifically engineered to work in the toughest concrete and steel where other pins cannot perform.
The new T4MAG system delivers power that rivals other gas and powder systems.
- Higher stick rate than the industry standard
- 30% more power to work in the toughest concrete
- Drives pins flush to create full embedment
- Lower pushdown force and shorter travel distance decrease user fatigue
- Reduced jamming, resulting in less downtime on the job
- Superb balance leads to optimal user experience
Power
Powered by a Lithium-Ion battery so no cords or hoses to get in the way.
Capacities
GAS FASTENERS IN STEEL
(INCH) | SHANK | ALLOWABLE LOAD – Ultimate Load | ||||||
Note 1: ALLOWABLE loads are shown in the LARGE BOLD font, Ultimate loads are shown in smaller italic font. Note 2: Testing conducted in accordance with ICC AC70 & ASTM E1190. Note 3: Safety factors are based on the coefficient of variation. In accordance with ICC AC70, the safety factor will be no less than 5. Note 4: Cyclic, fatigue, shock loads, and other design criteria may require a different safety factor. Note 5: Job site testing may be required to determine actual job site values. Note 6: Values shown are for fastenings that have the entire pointed end of the fastener driven through the steel plate; except as noted below. Note 7: Fastener penetration is .31″ minimum. Note 8: Fastener penetration is .29″ minimum. Note 9: Fastener penetration is .27″ minimum. Note 10: Fastener penetration is .25″ minimum. Note 11: For SI: 1 lbf = 4.448 N, 1 inch = 25.4 mm, 1 ksi = 6.89MPa
COLLATED GAS FASTENERS IN CONCRETE
NUMBER SERIES | DIAMETER (INCH) | PENETRATION (INCH) | ||||||
Straight Shank | ||||||||
NUMBER SERIES | DIAMETER (INCH) | PENETRATION (INCH) | ||||||
LIGHTWEIGHT CONCRETE | LIGHTWEIGHT CONCRETE WITH METAL DECK | UNITS (CMU) ANY LOCATION | ||||||
Straight Shank | ||||||||
Note 1: ALLOWABLE loads are shown in the LARGE BOLD font, Ultimate loads are shown in smaller italic font. Note 2: Testing conducted in accordance with ICC AC70 & ASTM E1190. Note 3: Safety factors are based on the coefficient of variation. In accordance with ICC AC70, the safety factor will be no less than 5. Note 4: Values shown in concrete are for the fastener only. Connected members must be investigated separately. Note 5: Cyclic, fatigue, shock loads, and other design criteria may require a different safety factor. Note 6: Job site testing may be required to determine actual job site values. Note 7: Minimum edge distance in concrete is 3 inches unless otherwise approved. Note 8: For SI: 1 lbf = 4.448 N, 1 inch = 25.4 mm, 1 ksi = 6.89MPa. Note 9: T3 straight shank allowable tension value in face shell of hollow CMU is 133 lbs.
Certifications, Standards, and Regulations
- ICC ESR 1955 - Fasteners
- COLA RR-22668 - Fasteners
In the Box
The following is included with this Direct Fastening Tool(T4MAG):
- (1) T4Mag Tool
- (1) Safety Glasses
- (1) User Guide & Safety Manual
- (2) Lithium-Ion Batteries
- (1) Battery Charger
Accessories Sold Separately.
Vendor Part #: | T4MAG |
Battery Chemistry: | Lithium-Ion |
Battery Style: | Stick |
Capacity: | 3/4 to 1 inch |
Capacity Steel: | 20, 18, 16 & 14 Ga. |
Height: | 16-1/4 inches |
Length: | 17 inches |
Weight: | 8.55 lbs. |
Magazine Capacity: | 45 pins |
Capacity Concrete: | 45 MPa Strength |
Max Pin Length: | 1 inch |
Battery Capacity: | 3500-Shots |
Fuel Cell Capacity: | 1000-Shots |
Pin Guide O.D.: | 590 |
- √Drive Pins Flush into Concrete
- √Installing Track to Concrete
- √Installing Track to Steel
- √Installing Deep Leg Track
- Article | IP Ratings Learn more about what an IP rating is and how this rating system is used.
https://www.calfast.com/cs_wiki/wiki/47-ingress-prot...